Post new topic Reply to topic  [ 5 posts ] 

Board index : TeleFlow Forums : TeleFlow Designer & Simulator

Author Message
 Post subject: Problems with Place Call step
PostPosted: Thu Feb 11, 2010 9:11 am 
Offline

Joined: Thu Feb 11, 2010 9:01 am
Posts: 5
We are developing an outbound application using CT Developer Studio 2 with a Dialogic D240JCT-T1 and everything works fine up until the place call step. The program thinks that the user has successfully answered their telephone when they did not and moves on to play a message for the user. This is happening for every phone I've tested it on. Below is some of the output from a test call I just tried. Any help would be greatly appreciated.



2010/02/11 11:06:16.404: Outbound_Main==>Outbound_Call
2010/02/11 11:06:16.404: [1] START
2010/02/11 11:06:16.404: [8] Connect Point
2010/02/11 11:06:16.404: [4] Place Call
2010/02/11 11:06:16.404: Telephone Number '@OUTCALLNUM' evaluates to '3302802210'
2010/02/11 11:06:16.404: Rings before TIMEOUT is '3'
2010/02/11 11:06:16.404: Do not capture answering voice length to TeleFlow variable
2010/02/11 11:06:16.404: Silence timeout is ''
2010/02/11 11:06:16.404: Empty Silence timeout defaults to none
2010/02/11 11:06:16.404: Maximum voice length timeout is ''
2010/02/11 11:06:16.404: Empty Maximum voice length timeout defaults to none
2010/02/11 11:06:16.404: ISDN Calling Number Plan is 'DEFAULT'
2010/02/11 11:06:16.404: ISDN Calling Number Type is 'DEFAULT'
2010/02/11 11:06:16.404: ISDN Called Number Plan is 'DEFAULT'
2010/02/11 11:06:16.404: ISDN Called Number Type is 'DEFAULT'
2010/02/11 11:06:16.404: Place call to 3302802210
and wait for up to 3 rings
2010/02/11 11:06:16.404: Do not connect on CED
2010/02/11 11:06:16.404: Do not connect on SIT
2010/02/11 11:06:16.404: Do not perform initial voice length detection.
2010/02/11 11:06:16.607: dt_getxmitslot, lines[curLine].tsdev = 11
2010/02/11 11:06:16.607: result = 0
2010/02/11 11:06:16.607: dx_getxmitslot, lines[curLine].chdev = 12
2010/02/11 11:06:16.607: result = 0
2010/02/11 11:06:16.607: dt_listen, lines[curLine].tsdev = 11, scbus timeslot = 0
2010/02/11 11:06:16.607: result = 0
2010/02/11 11:06:16.607: dx_listen, lines[curLine].chdev = 12, SCbus timeslot = 4
2010/02/11 11:06:16.607: result = 0
2010/02/11 11:06:16.607: Reset.
2010/02/11 11:06:16.607: ISDN Port's switch status has been reset
2010/02/11 11:06:16.607: cc_MakeCall, dev = 11, dial = '3302802210', rings = 3, timeout = 19 sec
2010/02/11 11:06:20.904: Setting system variable '@CALLOUT_RESULT' to 'CONNECT'
2010/02/11 11:06:20.904: Setting system variable '@CALLOUT_REASON' to 'CONNECT'
2010/02/11 11:06:20.904: cc_MakeCall succeeded, crn = -2147483641
2010/02/11 11:06:20.904: Setting system variable '@SYS_CALL_DIRECTION' to 'OUT'
2010/02/11 11:06:20.904: Setting system variable '@SYS_CALLREF' to ''
2010/02/11 11:06:20.904: [89] Set Global Variable
2010/02/11 11:06:20.904: Setting global variable '@CALLCOMPLETED' to '1'
2010/02/11 11:06:20.904: [21] Set Local Variable
2010/02/11 11:06:20.904: Setting local variable '@CALL_RESULT' to 'SUCCESS'
2010/02/11 11:06:20.904: [47] Set Global Variable
2010/02/11 11:06:20.904: Setting global variable '@VOX_APP' to 'Y'
2010/02/11 11:06:20.904: [36] Global Event
2010/02/11 11:06:20.904: Label is 'SAVE_RESULT'
2010/02/11 11:06:20.904: Setting system variable '@HANGUP' to 'SAVE_RESULT'
2010/02/11 11:06:20.904: [116] Clear TT
2010/02/11 11:06:20.904: [115] Run Flowchart
2010/02/11 11:06:20.904: Flowchart is 'MenuSet'
2010/02/11 11:06:20.904: Outbound_Call==>MenuSet
2010/02/11 11:06:20.904: [100] START
2010/02/11 11:06:20.904: [102] Set Global Variable
2010/02/11 11:06:20.904: Setting global variable '@COUNTER' to '3'
2010/02/11 11:06:20.904: [101] FINISH
2010/02/11 11:06:20.904: Outbound_Call<==MenuSet
2010/02/11 11:06:20.904: [63] Wait
2010/02/11 11:06:20.904: Delay is '1500'
2010/02/11 11:06:20.904: Waiting 1500 milliseconds
2010/02/11 11:06:22.404: [120] Play
2010/02/11 11:06:22.404: Script code is 'IntroMessage'
2010/02/11 11:06:22.404: Script code 'IntroMessage' corresponds to file 'Vox\Eng\Scripts\6E29E3EBFA19E6DDAB286AED1063179B.VOX'
2010/02/11 11:06:22.404: Playing 'C:\Documents and Settings\VMAdmin\Application Data\TeleFlow\Applications\Outbound\Vox\Eng\Scripts\6E29E3EBFA19E6DDAB286AED1063179B.VOX'
2010/02/11 11:06:24.388: [122] Wait
2010/02/11 11:06:24.388: Delay is '1500'
2010/02/11 11:06:24.388: Waiting 1500 milliseconds
2010/02/11 11:06:25.888: [57] Play
2010/02/11 11:06:25.888: Voice file name 'C:\\TeamTalk\@FILENAME' evaluates to 'C:\\TeamTalk\2010-02-10-11-55-06-39816353.save.VOX'
2010/02/11 11:06:25.888: Playing 'C:\\TeamTalk\2010-02-10-11-55-06-39816353.save.VOX'


Back to top
 Profile  
 
 Post subject: Re: Problems with Place Call step
PostPosted: Fri Feb 12, 2010 11:26 am 
Offline

Joined: Wed Mar 19, 2003 4:28 pm
Posts: 510
Location: Canada
I have a few questions for you on this before I can make any suggestions:
- What ISDN protocol variant are you running?
- What type of equipment is involved/is the T1 passing through?
- What version of Dialogic did you install?
- Where are you located?
- What happens when you do answer the phone? (are the phones ringing? can you answer the phone before the place call succeeds, and if so, what happens?)
- If you call those lines directory and no one answers, do they eventually answer in some way? (Eg. with voicemail?)


Back to top
 Profile WWW 
 
 Post subject: Re: Problems with Place Call step
PostPosted: Fri Feb 12, 2010 12:53 pm 
Offline

Joined: Thu Feb 11, 2010 9:01 am
Posts: 5
Hi Chris,

Currently I have the card set to 4ESS although I'm not sure if it's the right protocol. I need to contact out teleco and see what we should be using.

We have the Dialogic board installed in a Windows XP Professional machine with Service Pack 3.

Currently we have the System Release 6.0 installed. I know we should probably be using the 5.1.1 release but I recently upgraded it to try to solve another bug with an inbound app.

We are located in Dover, Oh

The thing is I can place a call to a couple of my coworkers and their cellphones ring and they can answer fine but when I place a call to my cell phone or anyone else the place call step says that it's connected and goes on to the next steps but my phone never rings and no voicemail picks the call up.

Thanks for the help,

Ted


Back to top
 Profile  
 
 Post subject: Re: Problems with Place Call step
PostPosted: Mon Feb 15, 2010 9:46 am 
Offline

Joined: Thu Feb 11, 2010 9:01 am
Posts: 5
I believe our problem might be that our t1 line isn't set up to make long distance calls. I'm able to place local calls but not long distance calls from it. My boss is checking with our teleco to see if we have long distance enabled on our plan.


Back to top
 Profile  
 
 Post subject: Re: Problems with Place Call step
PostPosted: Mon Feb 15, 2010 2:54 pm 
Offline

Joined: Wed Mar 19, 2003 4:28 pm
Posts: 510
Location: Canada
Sounds like you're starting with the right issues.

The protocol variant doesn't always matter, but, when it does, you may get anything from a system that doesn't work at all to one that has miscellaneous problems (which is what you could be seeing).

System Release 6.0 is fine.

As for the LD, that's a good thing to check. Are you adding a leading "1" to the dial string for LD calls? And, is calling your cell phone a long distance call relative to the T1?

You'll also want to know what these should be set to in the Place Call step:
ISDN calling number plan
ISDN calling number type
ISDN called number plan
ISDN called number type


Back to top
 Profile WWW 
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

Board index : TeleFlow Forums : TeleFlow Designer & Simulator


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Style by Midnight Phoenix & N.Design Studio
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.