Post new topic Reply to topic  [ 7 posts ] 

Board index : TeleFlow Forums : TeleFlow Installation

Author Message
 Post subject: TeleFlow services failed to install
PostPosted: Tue Feb 20, 2007 8:33 am 
Offline

Joined: Sat Feb 17, 2007 8:54 am
Posts: 8
TeleFlow installed and works in console mode, but services did not install.
Environment is Windows Server 2003 R2 Standard Edition


Back to top
 Profile  
 
 Post subject: Details of support request.
PostPosted: Tue Feb 20, 2007 12:01 pm 
Offline
Site Admin

Joined: Wed Dec 31, 1969 5:00 pm
Posts: 329
Location: Vancouver, BC
I am 90% certain that you do not have administrative rights to that machine. I will post a full answer momentarily. First, we need the details of your earlier support request as well, for continuity:

-----

The NMS AG 4040 card appears to be functioning properly.

The teleflow services did not install. I tried uninstalling/reinstalling/rebooting many times, but they would not install. I could manually install “TFSysBootTime_Service” but could not manually install “TFServer” service.

I started TFServer manually in console mode.

The teleflow monitor is showing red for all ports.


Back to top
 Profile WWW 
 
 Post subject:
PostPosted: Tue Feb 20, 2007 12:23 pm 
Offline

Joined: Sat Feb 17, 2007 8:54 am
Posts: 8
After sending you the email with the intial problem, I re-imaged the server and re-installed TeleFlow. I intentionally logged in as the local Administrator to elimated that as an issue. The services did not install. I have not tried to install them manually yet.

Does the installer use "InstallCompletor.bat"?
If so, it will not work properly for this reason:
TFDIR=D:\TeleFlow\
HOMEDRIVE=P:
The first line in "InstallCompletor.bat" is "cd %TFDIR%" which will not work since the drive is set to "P:". Need to first set drive to "D:"
Maybe that is the reason the services did not install?


Back to top
 Profile  
 
 Post subject: Troubleshooting TeleFlow install
PostPosted: Tue Feb 20, 2007 12:30 pm 
Offline
Site Admin

Joined: Wed Dec 31, 1969 5:00 pm
Posts: 329
Location: Vancouver, BC
I suspect you may have a user rights issue that is preventing the service from being installed. The TFSysBootTime_Service does very very little, and does not require administrative rights to the machine. In fact, in the version of TeleFlow you have, it is no longer required. I recommend you remove it as follows:

TFSysBootTime_Service REMOVE

Log-in as the local Administrator for that machine, and you should be able to install TeleFlow Server as a service. The command to install TFServer is as follows:

TFServer INSTALL "%TFDIR%"\"TFServer.exe SERVICE"

You should be able to type the command exactly as it appears above. %TFDIR% is an environment variable that should have been set by the TeleFlow installer.

This does not however, answer why the TeleFlow applications are failing (the Monitor showing red on all ports). Within the logs is the following:

[55] Wait for Call
: TIMEOUT is '0'
: WARNING: TIMEOUT '0' evaluates to 0 and is interpreted as no timeout
: Rings is '0'
: Connection Delay is '500'
: Wait for 0 rings and then pickup
: Open port 1, protocol 'wnk0'
: Port requested exceeds number of ports installed in the system
: ERROR: WaitForCall failed to open port

TeleFlow cannot access the channels on the card. This is an indication that the card is not configured properly. In order to help you with that I will need to see the NMS configuration files.

Please email support@engenic.com, with the following files attached:
    C:\nms\oam\cfg\oamsys.cfg
    C:\nms\ag\cfg\*.cfg (zipped)

Let me know the results of the above, and we'll follow up from there.


Back to top
 Profile WWW 
 
 Post subject:
PostPosted: Tue Feb 20, 2007 12:34 pm 
Offline
Site Admin

Joined: Wed Dec 31, 1969 5:00 pm
Posts: 329
Location: Vancouver, BC
That's it, all right. TeleFlow pretty much expects to be installed on C:
You should be able to install TeleFlow Server manually if you follow the steps of the InstallCompletor.bat.


Back to top
 Profile WWW 
 
 Post subject:
PostPosted: Tue Feb 20, 2007 12:39 pm 
Offline
Site Admin

Joined: Wed Dec 31, 1969 5:00 pm
Posts: 329
Location: Vancouver, BC
You may also want to check the registry values under this key:

HKEY_LOCAL_MACHINE\SOFTWARE\enGenic\TeleFlow Server

Anything that contains a full path (eg: C:\Program Files\TeleFlow\) should specify the path to where you've installed TeleFlow.

I'm sure I don't have to tell you to be very very careful while your in there ;-)


Back to top
 Profile WWW 
 
 Post subject:
PostPosted: Wed Feb 21, 2007 11:02 am 
Offline

Joined: Sat Feb 17, 2007 8:54 am
Posts: 8
TeleFlow service was manually installed successfully.


Back to top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

Board index : TeleFlow Forums : TeleFlow Installation


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Style by Midnight Phoenix & N.Design Studio
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.